admin
Moderator
Since 1.128 software needs to be installed with the latest setup file : https://scorpio-lk.com/downloads-tango.html
Also Windows admin privileges must not be given to any of the executable files.
1.130
- Thread starter admin
- Start date
Also Windows admin privileges must not be given to any of the executable files.
admin
Moderator
Проверил, у меня все работает
bahadur1987
New member
привет всем, уважаемый Любомир исправьте пожалуйста определения чипа 4D LKP-02 после генерации, не правильно определяет айди ключа, я вам фото отправлял на почту.... последной обнове все так же не работает.....
SF Auto Keys
Member
hello Admin,
reporting "possible bugs" to look into for future updates
I just received 10 pieces of LKP-06 today. Playing around with them and just noticed that the feature to clone smart key P1:98 is not there anymore, clone P1:94 to LKP-02, or P4:AA to LKP-04 or LKP-06 are there still but no vehicle available to confirm if the cloned LKP-xx would be able to start the vehicle or not.
I have successfully using SLK-08 to turn on the vehicle and to program another smart key (HYQ14FBA, 0020G board) for 2016 Lexus ES300h (USA market), P4:88. I was trying to clone the smart key to LKP-06, Tango was able to read the smart key, decoded, and gave out 2 options to clone to SLK-xx or LKP-06, I chose LKP-06, take out the smart key and insert the transponder to Tango, Tango never be able to detect the LKP-06 (it was like no LKP-06 there or the software is mistakenly commanding Tango to read/look for the LKP-06 at "somewhere else". Without moving the LKP-06, I aborted clone mode and just use read transponder, Tango read it perfectly fine at the same location where the clone mode was.
Please look into these when you get a chance. More to report eventually.
thanks a bunch!
reporting "possible bugs" to look into for future updates
I just received 10 pieces of LKP-06 today. Playing around with them and just noticed that the feature to clone smart key P1:98 is not there anymore, clone P1:94 to LKP-02, or P4:AA to LKP-04 or LKP-06 are there still but no vehicle available to confirm if the cloned LKP-xx would be able to start the vehicle or not.
I have successfully using SLK-08 to turn on the vehicle and to program another smart key (HYQ14FBA, 0020G board) for 2016 Lexus ES300h (USA market), P4:88. I was trying to clone the smart key to LKP-06, Tango was able to read the smart key, decoded, and gave out 2 options to clone to SLK-xx or LKP-06, I chose LKP-06, take out the smart key and insert the transponder to Tango, Tango never be able to detect the LKP-06 (it was like no LKP-06 there or the software is mistakenly commanding Tango to read/look for the LKP-06 at "somewhere else". Without moving the LKP-06, I aborted clone mode and just use read transponder, Tango read it perfectly fine at the same location where the clone mode was.
Please look into these when you get a chance. More to report eventually.
thanks a bunch!
Last edited:
bahadur1987
New member
Привет всем, уважаемый Админ последной обнове все так же не работает у меня генерация чипа LKP-02 на id67 или 68, танго правельно генерить чип но при определения как RF430 определяет, раньше версии 1.128 пару лет норм работала, исправьте это пожалуйста очень не удобна, заранее спасиба
admin
Moderator
We don't observer such behavior from LKP-02, regardless of configuration (ID60, 67, 68, 70, G), the only quirk regarding its current detection is that it can be seen as TPX2 while in 4D mode, other than that there is no way for Tango to see it as RF430, especially given that LKP-02 doesn't support 128bit mode.
Also there are no other reports from other users with an issue like yours, this leads to a conclusion that there is some problem at your side.
1. The transponders you have are faulty.
2. Very bad connection between Tango and your PC.
3. Unlikely but possible, you got some other transponder dropped and stuck inside your Tango near the coil and it messes up the reads.
Im having same exact issue. Tango software shows support for PG4: 88 but when I write, I get write error. So Tango software issue or bad chips.
Attachments
I got the same error on 8A-AA. What is the cause?