Search results

Hi is this supported by barracuda mk4 Yaris hybrid keyed ignition thanks MARTYN

we have read the 93c56 in ecu as 16 bit ,tango wont recognise it ,in anything or autodetect ,can see the key data another tool TM*** recognises it but no licence ,tried lexus models & loads of others same chip ,can tango admin check it please thanks

hi bought a brandnew full tango from mk3.com emirates keys ********************its faulty wont read 4d chips they say hardware fault ,we have done everything reinstall usb tests etc other tango works fine were struggling with 2 vans without it they want me to return it to them then them to you...

We have latest 6.7 & g box immo reset by obd and this says no cars detected with ignition on or off , I though this was meant to do the European g box immo resets Other tools inc avdi connected but also failed Is this not covered in this module Thanks Martyn

Struggling to find latest version. Or any version for that matter , can someone please enlighten me please

Tried 10 of these keys , unlocked all ok no issues car won’t accept any It’s me key part number & same pcb as v9 Nissan and in pictures I post Programmed copy key first go Tried all other pcf7953 too

hi can anyone sync this ecu & immo or supply matched set thanks in advance immo 24c04 ecu 95040

Tango plus reset immobiliser in seconds & we added 2 I’d 67 master keys obviously correct page info for key 1 & key 2 , car runs but immo light flashes constantly , go in with tech stream sees 2 master keys & immo under but won’t allow to add or delete keys as they are not fully in as suspect...

Hi all , having murders with this , it’s last of old shape Yaris but has an 80 bit immo on it , reset by obd using tango plus , didn’t know it was Tokai Rika , added key one 80 bit page 1 37 , it took it , wouldn’t not add key 2 80 bit page 1 57 & would not run , says added key 2 but key count...

I pretty much knew this would be a no brainier but had a look anyway Tango connects but can’t read data due to no security access Tried AVDI reset , failed Opened smart ecu found 95160 eprom , customer would not let me read it or take it away Does anyone know if tango will eprom it or...

Hi has anyone ever done one of these , looking for info , was just a plain key id46 , probably needs a specially prepared transponder so may need dealer ordered key , any info greatly appreciated as tango don’t list it , AVDI don’t list it Thanks in advance martyn

Tried tango plus v6.6 on above vehicle , connects to immo shows part number & h key , press reset & get error 21 just in case anyone quotes for obd We were using genuine AVDI as passthru So that’s tested & does not work We had to do it normal way by swapping immobox for new virgin unit &...

Early 2012 Yaris , total lost keys , proximity key Does anyone have any info like module that needs changing As no info anywhere on id46 system Thanks in advance Martyn

Also has part no 906 545 26 08 need correct flash as critical on crafter flash matches EPROM and don't have any k just j Thanks Martyn

Hi has anyone got a pin out for this box , I think it's knackered as another locksmith has used pin outs for 147 with different chip & said can't recognise chip Thanks in advance Martyn

Having bought the dp3 2 years ago everything was great as I didn't need to have any interaction with the company Upgraded to dp4 that's when problems started ! Needs different cables which they didn't have & didn't tell me it needed So had to keep using dp3 & it's cables ! They sent me a dp4...

Got this however I'm having loads of issues with it Won't read any passwords always says licence not active ! Roy says he's fixed it so update & still never works Always says error data transfer when trying to do stuff & lost count of nec chips it's damaged reading password

Just seen this being offered full kit with some crappy firmware update tool full kit 800 usd Seems nothing is safe maybe time for a hardware change or any measure to protect it I for one would be happy to pay for a new interface to protect The work of tango team

Hi is it possible if I send files to make tango recognise cas 4 plus and ask for Isn or working key I have files read from 5m48h & 1n35h up to 2014 if needed Thanks Martyn I'm sure could be added as payable option